Retail Control Version 3 Error messages

-827 Error setting up Break con

-828 Comms Link couldn't be opened

-829 Comms Link couldn't be closed

-830 Bad Handshaking Mode requested

-831 Attempt to change read only line

-832 Argument to function is bad

-833 System call failed

-834 Error during write operation

-835 Error during read operation

-836 A memory allocation failed

-838 Link is already open

-839 Used an unsupported baudrate setting

-840 Used an unsupported parity setting

-841 Used an unsupported stopbit setting

-842 Used an unsupported wordlength setting

-843 Device driver not installed

-844 This device driver is not supported

-845 The driver had a general failure

-846 This board number is not installed

-847 The user has selected to abort

-848 There was no OK from modem in specifed time

-849 This board has already been configured

-850 No GFSerial object is attached to class in use

-851 An error occured using DOS extender API

-852 This IRQ is already used by another comm port

-853 Tried to hook more than the allowed IRQs

-854 General Error, non-specfic.

-855 A error occured using the NASI interface.

-856 NASI.EXE or NASI.DLL was not setup properly.

-857 Unable to connect to a modem on a NASI server.

-858 Win 32s thunking layer failed to initialize.

-859 No default base address above COM4.

-901 User cancelled

-902 File open error

-903 File read error

-904 File write error

-905 File close error

-906 Transfer error

-907 To many retries

-908 To many errors

-909 Timeout error

-910 RX EOF error

-911 TX EOF error

-912 End of transfer error

-913 Sync. error

-914 Remote cancelled

-915 Init not acknowledged

-916 Packet NAK'ed

-917 Previous packet received

-918 Packet integrity error

-919 File header error

-920 Insufficient memory for transfer

-921 Internal logic error

-922 Can't send NACK

-923 Can't send ACK

-924 Can't put char

-925 Can't put buffer

-926 Can't find a filename

-927 File Engine not created

-928 Protocol error

-929 Lost carrier signal

-930 Can't get char

-931 General Transfer error

-932 Sent no files

-933 Receiver should send ZSKIP

-934 Bad packet sequence

-935 Packet arrived

-950 File engine pointer not NULL

-951 File engine open failed

-952 File engine close failed

-953 File engine invalid pointer

-954 File engine unable to set position

-955 File engine unable to get position

-956 File engine insufficent memory

-957 File engine time/date error

-1000 Can't disable Power Management

-1001 Doesn't like file name

-1002 No 'Direction' specified in command

-1003 No 'Protocol' specified in command

-1004 No 'DOS File' specified in command

-1005 No 'ID ENQ' received

-1006 No 'ACK' received

-1007 No 'STX' received

-1008 Backup failed

-1009 Can't read ini defaults

-1010 Invalid Mode

-1011 Invalid equation

-1012 Invalid expression

-1013 Invalid field name

-1014 Invalid file number specified

-1015 Invalid command line

-1016 Invalid operator

-1017 Invalid protocol

-1020 No response from BarCode printer

-1021 Can't read send file

-1022 Received EOT

-1023 Can't read data from file

-1024 Can't write data to file

-1025 Can't write file time

-1026 Field "FileID" not found

-1027 File has no records

-1028 Field "FieldID" not found

-1029 Can't save screen

-1030 Too many columns specified

-1031 Line toooooo long

-1032 Can't load features

-1033 Can't find field

-1034 Can't find file

-1035 Can't create recordset

-1036 No input file specified

-1037 No output file specified

-1038 Column error

-1039 No data header

-1040 No memory

-1041 Source file doesn't exist (Polyglot)

-1100 Failed Criteria check